Engineering · Year 1
Electronics and Robotics: interactive labs
Components, Arduino, sensors and motors. Each lab is a live bench in your browser: change a value, predict what happens, then watch the readings, the graph and the working update. Free on Stranerd.
40 labs in Electronics and Robotics
- 1Ohm's law and resistorsVoltage pushes, resistance holds back, current is what you get.
- 2Series and parallelTwo ways to join parts, and two sets of rules.
- 3The voltage dividerTwo resistors make any voltage you need.
- 4LEDs and series resistorsAn LED needs a resistor to stay alive.
- 5Capacitors and timingA resistor and a capacitor make a clock.
- 6DiodesA one-way valve for current.
- 7Half-wave rectifierKeep half the wave, and smooth what is left.
- 8Bridge rectifierFour diodes use both halves of the wave.
- 9Zener regulatorsHold a steady voltage from a shaky supply.
- 10Transistor as a switchA small current controls a big one.
- 11Transistor amplifierTurn a small wave into a big one.
- 12MOSFETsVoltage on the gate, and almost no loss when fully on.
- 13Op-amp: inverting amplifierTwo resistors set the gain.
- 14Op-amp: non-inverting amplifierGain without turning the signal over.
- 15ComparatorsTwo voltages in, one yes or no out.
- 16The 555 timerOne chip, two resistors, one capacitor, and a steady beat.
- 17Logic gatesEverything a computer does, from a few small rules.
- 18Flip-flops and countersCount in ones and zeros.
- 19Analogue to digitalTurn a smooth voltage into a number.
- 20Pulse width modulationFake a voltage by switching very fast.
- 21Arduino: blinkYour first sketch.
- 22Arduino: buttonsRead a switch, and why a pin must never float.
- 23Arduino: analogue inputA knob becomes a number from 0 to 1023.
- 24Arduino: fading an LEDanalogWrite is really PWM.
- 25Light sensorsBuild a lamp that comes on at dusk.
- 26Temperature sensorsRead a TMP36 and do the sum in code.
- 27Ultrasonic distanceShout, listen, and time the echo.
- 28Servo motorsThe length of a pulse is the angle.
- 29DC motors and H-bridgesRun a motor both ways from one supply.
- 30Stepper motorsMove by counted steps, with no sensor.
- 31EncodersCount slots to measure speed.
- 32Line sensorsSee a black line with reflected light.
- 33The I²C busMany devices on two wires.
- 34Differential driveSteer with no steering wheel.
- 35Gear ratiosTrade speed for torque.
- 36Line-following robotTune it so it stops swerving.
- 37Obstacle avoidanceStop before you hit it.
- 38PID controlReach the target and stay there.
- 39Robot arm kinematicsJoint angles decide where the hand goes.
- 40Battery and power budgetHow long will your robot really run?
Other courses
Year 2GET 201 Applied ElectricityDC and AC circuits, from fields and Kirchhoff’s laws to impedance.Year 2GET 207 Applied MechanicsForces, equilibrium and motion in real structures.Year 2GET 208 Strength of MaterialsStress, strain, bending, torsion and buckling.Year 2GET 205 Fluid MechanicsPressure, flow, pipes, pumps and turbines.Year 2GET 206 ThermodynamicsHeat, work, the laws and engine cycles.Year 2GET 202 Engineering MaterialsWhy metals, ceramics and polymers behave as they do.Year 1GET 102, 203 Graphics and Solid ModellingProjections, working drawings and 3D parts.Year 1GET 204 Workshop PracticeTools, measuring, machining and safety.